AT070TN92 7寸TFT液晶屏资料

群创光电7才数字屏，苏州联凯光电代理群创液晶屏如有需要欢迎来电垂询INNOLUXContents1. General Specifications2. Pin Assignment.…3. Operation Specifications3.1. Absolute Maximum Rating3.1.1. Typical Operation Conditions......3.1.2. Current Consumption2556773.1.3. Backlight Driving Conditions32. Power Sequence…………3.3. Timing Characteristics3.3.1 AC Electrical Characteristics3.3.2. Data Input Format103.3.3. Timing4. Optical specifications125. Reliability Test items6. General Precautions6.1. Safety…176.2. Handling6.3. Static Electricity6.4. Storage..176.5. Cleaning7. Mechanical Drawing8. Package Drawing..…8. 1 Packaging Material Table8.2 Packaging Quantity8.3 Packaging Drawing20量售有,止任何的使用The copyright belongs to InnoLux. Any unauthorized use is prohibitedINNOLUXSPEC NO.:A070-92-TT-02Date:2009/06/22Page: 1/201. General SpecificationsNoItemSpecificationRemark1 LCD size7.0 inch(Diagonal)2 Driver elementa-Si TFt active matrix3 Resolution800×3(RGB)×4804 Display modeNormally White, Transmissive5 Dot pitch0.0642(W)×0.1790(H)mm6 Active area15408W)×8592(H)mm7 Module size1649(W)×100.0(H)×57(D)mmNote 18 Surface treatmentAnti-Glare9 Color arrangementRGB-stripe10 InterfaceDigitalBacklight power consumption 1.674W(Typ.12 Panel power consumption0226W(Typ.)13 Weight(150g)(Typ.)Note 1: Refer to Mechanical Drawing量售有,止任何的使用The copyright belongs to InnoLux. Any unauthorized use is prohibitedINNOLUXSPEC NO.:A070-92-TT-02Date:2009/06/22Page: 2/202. Pin AssignmentTFT LCD Panel Driving SectionFPC Connector is used for the module electronics interface the recommended model isFH12A-50S-05SH manufactured by hirosePin No. SymbolvOFunctionRemarkLED+P Power for LED backlight (Anode)2LED+P Power for LED backlight(Anode3VLEDP Power for LED backlight(Cathode)VLEDP Power for LED backlight(Cathode)456789GNDPPower groundCOMI Common voltageDVDDPPower for Digital CircuitMODEDE/SYNC mode selectNote 1DEData Input enable10VSVertical Sync Input11HSHorizontal sync Input12B7Blue data( MSB)13B6Blue data14B5I Blue data15B4Blue data16B3Blue data17B2Blue data18B1Blue dataNote 219BOI Blue data(LSB)Note 220G7I Green data(MSB)21GGreen data22G654Green data23GGreen data24G3Green data25G2Green dataThe copyright belongs to InnoLux. Any unauthorized use is prohibitedINNOLUXSPEC NO.:A070-92-TT-02Date:2009/06/22Page: 3/2026G1Green dataNote 227GOGreen data(LSB)Note 228R7I Red data(MSB)29R6Red data30R5Red data31R4Red data32R3I Red data33R2Red data34R1Red dataNote 235ROI Red data(LSB)Note 236GNDPower ground37DCLKSample clockNote 338GNDPower ground39L/RLeft/ right selectionNote 4.540U/DUp/down selectionNote 4.541GHGate oN Voltage42GLPPPGate OFF Voltage43AVDDPower for Analog Circuit44RESETGlobal reset pinNote 645NCNo connection46COMCommon voltage47DITHBDithering functionNote 748GNDPower ground49NCNo connection50NCNo connection1: input, O: output, P: PowerNote 1: DE/SYNC mode select Normally pull highWhen select dE mode, ModE=1",vs and hs must pull highWhen select SYNC mode, MODE=0, DE must be groundedNote 2: When input 18 bits rgb data, the two low bits ofr, g and b data must begroundedNote 3: Data shall be latched at the falling edge of DCLK的使用The copyright belongs to InnoLux. Any unauthorized use is prohibitedINNOLUXSPEC NO.:A070-92-TT-02Date:2009/06/22Page: 4/20Note 4: Selection of scanning modeSetting of scan control inputScanning directionU/DL/RGNDDVDDUp to down, left to rightDVDDGNDDown to up, right to leftGNDGNDUp to down, right to leftDVDDDVDDDown to up, left to rightNote 5: Definition of scanning directionRefer to the figure as belowUpLeftC→RghtDownNote 6: Global reset pin. Active low to enter reset state. Suggest to connect with an RCreset circuit for stability. Normally pull highNote 7: Dithering function enable control, normally pull highWhen DITHB=1, Disable internal dithering functionWhen DITHB=0, Enable internal dithering function量售有,止任何的使用The copyright belongs to InnoLux. Any unauthorized use is prohibitedINNOLUXSPEC NO.:A070-92-TT-02Date:2009/06/22Page: 5/203. Operation Specifications3.1. Absolute Maximum Ratings(Note 1ValuesItemSymbolUnit RemarkMinMDVDD0.35.0AVDD6.5135Power voltage-0.340.0GL0.3VGH-VGL40.0Operation TemperatureTop-2070Storage TemperatureV√√V℃℃VST3080LED Reverse VoltageVR1.2Each LEDNote 2LED Forward current25ma Each LEDNote 1: The absolute maximum rating values of this product are not allowed to be exceededat any times. Should a module be used with any of the absolute maximum ratingsexceeded, the characteristics of the module may not be recovered, or in an extremecase, the module may be permanently destroyedNote 2: Vr Conditions: Zener diode 20mA量售有,止任何的使用The copyright belongs to InnoLux. Any unauthorized use is prohibitedINNOLUXSPEC NO.:A070-92-TT-02Date:2009/06/22Page: 6/203.1.1. Typical Operation ConditionsNote 1)ValuesItemymboUnit RemarkMinMaxDVI3.03.33.6Note 2AVDD10.210.410.6Power voltageGH15.316016.77.76.3Input signal voltageICOM3.84.04.2Input logic high voltageH0.7 DVDDDVDDNote 3Input logic low voltage00.3 DVDDNote 1: Be sure to apply DVdd and Val to the LCD first, and then apply vghNote 2: DVDD setting should match the signals output voltage(refer to Note 3)ofcustomer's system boardNote 3: DCLKHS VS.RESETU/D, L/R DE.RO-R7 G0-G7B0-B7 MODE DITHB.量售有,止任何的使用The copyright belongs to InnoLux. Any unauthorized use is prohibitedINNOLUXSPEC NO.:A070-92-TT-02Date:2009/06/22Page: 7/203.1.2. Current ConsumptionaluesSymbolItemUnit RemarkMin. Typ.MaxGH0210 mA VGH=16.0GL0.21.0 mA VGL=-70VCurrent for driverIDVDD4.010mA DVDD=3.3VIAVDD2050 mA AVDD =10.4V3.1.3. Backlight Driving ConditionsValuesItemSymbolUnitRemarkMinp. MaxVoltage for lEd backlightVL8.79.3NoteCurrent for LEd backlightlL17080200ALED life time20.000Note 2Note 1: The LEd Supply Voltage is defined by the number of led at Ta=25C and1L =180mANote 2: The"LED life time" is defined as the module brightness decrease to 50% originalbrightness at Ta=25C and Il =180mA. the led lifetime could be decreased ifoperating IL is lager than 180mA量售有,止任何的使用The copyright belongs to InnoLux. Any unauthorized use is prohibited