COPAL CS 32 转动选择开关(Selector Switches).pdf

COPAL CS-32 转动选择开关（Selector Switches）pdf,COPAL CS-32 转动选择开关（Selector Switches）COPAL ELECTRONICSCS-32ROTARY SELECTOR SWITCHES ( SMDSTANDARD SPECIFICATIONSELECTRICAL CHARACTERISTICSCircuit type1 pole 2 contactsContact rating0.5VAOperating temperature rangeMaximum current100mA40~85°0Maximum voltage16VStorage temperature rangeSealingWashable by"“ 0"ringContact timingNon-shortingApprox 0.05g(A, B)Contact resistance2 maximumNet w/eightApprox 0.06g(C)Appro×.0.11g(G,H)Insulation resistance100 MQ(DC500V)minimumDielectric strengthAC250V,60sMECHANICAL CHARACTERISTICSNo. of positionsENVIRONMENTAL CHARACTERISTICSAdjustment torque5 mN.m 151 gf-cm) maximumAmplitude 1.5 mm orStopper strengthAcceleration 98 m/s220 mN m (204 gfcm) minimumVibration10-500-10Hz,3 directions for 10 cycles eachStepping angle250°±15°Shock490m/s2,11e directions for 3 times eachSolderabilitysnCu(ead-re):245±3°c.2~3sLoad life50 cycles minimumDC16V30 mAHumidity(Steady state)40C, Relative humidity 90-95/, 240 hSn-Cu(Lead-treeHigh temperature exposure85°C.96hFow:260±3° as the temperaturein a pot of molten solderemersion from head of ter-LoW temperature exposure40°C.96hSoldering heatminal to backside of board5-6s two times maximumThermal shock-40(0.5h)~85°C(0.5h).5 cyclesReflow: Peak temperature 255C( Please refer to the profile below.Manual soldering:350±10°C,3~4sShear(Adhesion)5N0.51kgf,10s(°C)250Peak:2500°CSubstrate bendingWidth 90 mm bend 3 mm. 5s. 1 timeover230°0Pull-off strength5N10.51kgf,10sg200Pre Heating Zone名180°0I 1: Reference only 2 150- 150 C90±30s10030±10s50Heating timeSoldering ZoneReflow: two times maximumSpecifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request. Jan,2007COPAL ELECTRONICSC5-37ROTARY SELECTOR SWITCHES ( SMD■ OUTLINE DIMENSIONSUnless otherwise specified, tolerance: +0.3(Unit: mm)●cs-32-12zEAProduction date codeLead- free ldentification mark1 dig t (Location reversed every 2 years)cW345Wx19-×0.45D0.05●cs-32-122EBProduction date codeLead- free Identificaticn mark1 digit (Location reversed every 2 years)cW340005M×19L×045D0.05●cs-32-12zEcProduction date code05W×1.9L×045DLead-free ldentification mark1 digit Location reversed every 2 years)t=0.12⊥2-0.73.44±1→TCMNo plating on the cut surface●cs-32-12zEGPrcduction date code02Operating face2-0.6Lead-free Identification mark1 digit(Location reversed every 2 years)CW, (C) CCW3.6t=0.12a Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request. Jan.2007COPAL ELECTRONICSCS-32ROTARY SELECTOR SWITCHES ( SMD■ OUTLINE DIMENSIONSUnless otherwise specified, tolerance: +0. 3(Unit mm)●Cs32-12ZEH3.5Prod」 ction dare code&0.5Wx1.9L×0.45DOperating faceLead-free ldentification mark1 digit i Location reversed every 2 years,c ccwt=0.123.6RECOMMENDED P.C.B. PAD OUTLINE DIMENSIONS●cs-32-12zEA,12ZEG●cs-32-12zEB.12ZEH(Unit: mm)4012081220812Note 1)The zero point is the center of mountingNote 2)The land patterns conform to EIAJ RC2161Note 3) The land patterns are for reflow solderingSpecifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request. Jan,2007COPAL ELECTRONICSC5-37ROTARY SELECTOR SWITCHES ( SMDPACKAGING SPECIFICATIONSO Taping version is packaged in 500 pcs per reelOrders will be accepted for units of 500 pcs, i. e, 500, 1000, 1500 pCS,, etcO CS-32ZETA and ZETB versions are boxed with 4 reels(2000 pcs. CS-32ZETG and ZETH versions are boxed with onereel (500 pcs.Maximum number of consecutive missing pieces =2Leader length and reel dimension are shown in the dia-grams belowO Embossed tape dimensions● Reel dimensionsUnit: mm)(Conforms to JIS C 0806-3)(In accordance with ElAJ ET-7200A)130(ETA/ETB)134∈ ETG/ETH)FillEnd囗…口囗图…-图团20 pitches minDirection of feedLeader/13+02400 mm min15.4+1 (ETAETBo 180-i5(Top setting type)17.4±1(ETG/ETH)254±2( de setting typeOCS-32-12ZETA/CS-32-12ZETBCS-32-12ZETG/CS-32-12ZETHnit: mm(Conforms to JIS C 08062+0050.4±0.1ation exampleInstallation example(CS-32EA)6+2Direr"ion of feedO The smallest unit of bulk pack in a plastic bag is 10 pcs per pack. Orders will be accepted for unit of minimum 10 pcs:1.e10,20,30pcs.,etcO Boxing of bulk in a plastic bag is performed with 100 pcs (standard 500 pcs. per boxa Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request. Jan.2007