MOC3021 M.pfd

6-PIN DIP RANDOM-PHASE OPTOISOLATORS TRIAC DRIVER OUTPUT(250/400 VOLT PEAK)6-PIN DIP RANDOM-PHASEARGH|L口OPTOISOLATORS TRIAC DRIVER OUTPUTSEMICONDUCTOR③(250/400 VOLT PEAK)MOC3010M MOC3011M MOC3012M MOC3020M MOC3021M MOC3022M MOC3023MELECTRICAL CHARACTERISTICS(TA=25C Unless otherwise specifiedINDIVIDUAL COMPONENT CHARACTERISTICSParametersTest ConditionsSymbol Device Min Typ Max UnitsEMITTERInput Forward voltageF=10 mAV11515VReverse Leakage CurrentVR=3V,TA=25CA001100pDETECTORPeak Blocking Current, Either DirectionRated VDRM, IF=0 (note 1)DRMAll10100nAPeak On-State Voltage, Either Direction ITM=100 mA peak, IF=0TMA1.83VTRANSFER CHARACTERISTICS(TA=25C Unless otherwise specified.DC CharacteristicsTest Conditions SymbolDeviceMinTypMaxUnitsMOC3020M30MOC3010M15MOC3021MLED Trigger CurrentVoltage=3V(note 3)IFMOC3011M10MOC3022MMOC3012M5MOC3023MHolding Current, Either DirectionHA100HANote1. Test voltage must be applied within dv/dt rating2. This is static dv/dt. See Figure 5 for test circuit. Commutating dv/dt is a function of the load-driving thyristor(s only3. All devices are guaranteed to trigger at an lF value less than or equal to max FT. Therefore, recommended operating lF liesbetween max lFT(30 mA for MOC3020M, 15 mA for MOC3010M and MOC3021M, 10 mA for MOC301 1M and MOC3022M,5 mA for MOC3012M and MOC3023M)and absolute max lF(60 mA)C 2002 Fairchild Semiconductor CorporationPage 3 of 98/8/026-PIN DIP RANDOM-PHASEARGH|L口OPTOISOLATORS TRIAC DRIVER OUTPUTSEMICONDUCTOR③(250/400 VOLT PEAK)MOC3010M MOC3011M MOC3012M MOC3020M MOC3021M MOC3022M MOC3023MFig. 1 LED Forward Voltage vs Forward CurrentFig. 2 On-State CharacteristicsuoomoH乙Ou==mzoON-STATE VOLTAGE·Vm()F-LED FORWARD CURRENT(mAFig 3 Trigger Current vs. Ambient TemperatureFig. 4 LED Current Required to Trigger vs LED Pulse WidthNORMALIZED TO:09NORMALIZED TOTA= 250oCER WIDTH-PWin (us)AMBIENT TEMPFRATURE-T。(°C)Fig 6 Leakage Current, IDRM VS TemperatureFig 5 dvidt vs TempcratureSTAtIC dv/ctAmbient Temperature -TA(C)TA, AMBIENT TEMPERATUREC 2002 Fairchild Semiconductor CorporationPage 4 of 98/8/026-PIN DIP RANDOM-PHASEARGH|L口OPTOISOLATORS TRIAC DRIVER OUTPUTSEMICONDUCTOR③(250/400 VOLT PEAK)MOC3010M MOC3011M MOC3012M MOC3020M MOC3021M MOC3022M MOC3023MThe mercury wetted relay provides a high speed repeated400V(MOC302Xpulse to the D.U.T.250V(MOC301XVdc2. 100X scope probes are used, to allow high speeds andR=10kvoltagesTESTPULSE3. The worst-case condition for static dv/dt is established byINPUTMERCURYtriggering the D U.T. with a normal LED input current, thenWETTED100RELAYASCOPEremoving the current. The variable RTesT allows the dv/dD U.T.PROBEto be gradually increased until the D U.T. continues totrigger in response to the applied voltage pulse, evenafter the led current has been removed the dv/dtthen decreased until the D.U.T. stops triggering tRc iSmeasured at this point and recorded400V(MOc302X)APPLIED VOLTAGE250V(MOC301XWAVEFORM252V(MOc302X)158V(MOc301X)63O VOLTS(MOC302X158Figure 5. static dv/dt Test circuitNote: This optoisolator should not be used to drive a load directlyIt is intended to be a trigger device only.RL2MOC3011MMOC3012MFigure 6. Resistive Load62.4k2|Moc3010M60 HzMOC3011M0.1 uF T CMOC3012Migure 7. Inductive Load with Sensitive Gate Triac (GT <15 mA)C 2002 Fairchild Semiconductor CorporationPage 5 of 98/8/026-PIN DIP RANDOM-PHASEARGH|L口OPTOISOLATORS TRIAC DRIVER OUTPUTSEMICONDUCTOR③(250/400 VOLT PEAK)MOC3010M MOC3011M MOC3012M MOC3020M MOC3021M MOC3022M MOC3023MR61801.2k2MOC301OM560 HZMOC3011M.2uF不C1MOC3012M4Figure 8. Inductive Load with Sensitive Gate Triac (GT $15 mA)R6360O HOT1OC3020MMOC3021MMOC3022M0.05μF不240MOC3023M4VAC0.01uFLOAD HO GROUNDIn this circuit the "hot side of the line is switched and the load connected to the cold or ground sideThe 39 ohm resistor and 0.01uF capacitor are for snubbing of the triac, and the 470 ohm resistor and0.05 uF capacitor are for snubbing the coupler. These components may or may not be necessarydepending upon the particular and load usedFigure 9. Typical Application CircuitC 2002 Fairchild Semiconductor CorporationPage 6 of 98/8/026-PIN DIP RANDOM-PHASEARGH|L口OPTOISOLATORS TRIAC DRIVER OUTPUTSEMICONDUCTOR③(250/400 VOLT PEAK)MOC3010M MOC3011M MOC3012M MOC3020M MOC3021M MOC3022M MOC3023MPackage Dimensions(Through Hole)Package Dimensions( Surface Mount)0.350(8890.320(8.13)0320(8P凸凸凸凸03909.90)260(6.601Q260(660)0321843)0.070(1.77040(1.020.320(8.13)0320(8.13)0.014(0.360.010(0250012(0.300008(0.20)000.100[20.100(254).01200.30)(0.41)0006Package Dimensions (0. 4 "Lead Spacing)Recommended Pad Layout forSurface mount leadform50(880320(813)凸凸0.070(1.78)F中□口0.060(1.52)0070(177)0.040(102)0.014(0360.010(0.250.425(10.79)0.100(254)0200(50305(775)0030(0.76)0.100(254)0.100[2540.12(030)0020(0.5000160.41)0425(1080)0400(10.16)NOTEAll dimensions are in inches(millimeters)C 2002 Fairchild Semiconductor CorporationPage 7 of 98/8/026-PIN DIP RANDOM-PHASEARGH|L口OPTOISOLATORS TRIAC DRIVER OUTPUTSEMICONDUCTOR③(250/400 VOLT PEAK)MOC3010M MOC3011M MOC3012M MOC3020M MOC3021M MOC3022M MOC3023MORDERING INFORMATIONOptionOrder Entry IdentifierDescriptionSurface mount lead bendSR2SR2Surface Mount; Tape and reel0.4 Lead SpacingVDE 0884TVTVVDE 0884, 0.4 Lead SpacingVDE 0884, Surface MountSR2VSR2VVDE 0884, Surface Mount, Tape& ReelCarrier Tape Specifications12.0±0.14.5±0.2020+0055 MIN0±0.11.75±0.1011.5±1.0210±0.1d24.0±0.39.1±0200.1 MAX10.1±02001.5±0.1/-0User direction of feedNOTEAll dimensions are in inches(millimeters)C 2002 Fairchild Semiconductor CorporationPage 8 of 98/8/026-PIN DIP RANDOM-PHASEARGH|L口OPTOISOLATORS TRIAC DRIVER OUTPUTSEMICONDUCTOR③(250/400 VOLT PEAK)MOC3010M MOC3011M MOC3012M MOC3020M MOC3021M MOC3022M MOC3023MDISCLAIMERFAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TOANY PRODUCTS HEREIN TO IMPROVE RELIABILITY FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUMEANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREINNEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS NOR THE RIGHTS OF OTHERSLIFE SUPPORT POLICYFAIRCHILDS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICESOR SYSTEMS WITHOUTXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTORCORPORATION. As used herein.1. Life support devices or systems are devices or systems 2. A critical component in any component of a life supportwhich, (a) are intended for surgical implant into the body, ordevice or system whose failure to perform can be(b)support or sustain life, and (c) whose failure to performreasonably expected to cause the failure of the life supportwhen properly used in accordance with instructions for usedevice or system, or to affect its satety or effectivenessprovided in the labeling, can be reasonably expected toresult in a significant injury of the userC 2002 Fairchild Semiconductor CorporationPage 9 of 98/8/02This datasheet has been download fromwww.datasheetcatalog.comDatasheets for electronics components